Specification Writers: These values are not intended for use in preparing specifications. Please contact your local DOWSIL sales office or your Global DOWSIL Connection before writing specifications on this product.
DIN 18545 E
ISO 11600 F 25LM (MORTAR UNPRIMED)
ISO 11600 G 25LM (FAÇADES & VITRAGES)
Surfaces must be cleaned, dry and free from grease and dust. Non-porous surfaces, such as aluminum, glass etc., should be cleaned with a suitable solvent for the substrate.
Porous substrates such as concrete, brickwork, mortar, etc. must be mechanically cleaned from loose particles using a steel brush, sanding disc, or any similar means. The use of a primer is recommended to obtain durable adhesion performance on such porous substrates, or if water immersion is expected to occur during the service life of the assembly. Otherwise, primers are not usually required but might be needed for some specific substrates to achieve optimum adhesion.
This product adheres to a variety of porous and non-porous substrates.
Users must carry out their own tests due to the great variety of substances. In many cases, adhesion can be improved by pretreatment of the substrates with a primer:
How to apply
DOWSILTM 799 EU Glaze and Go Neutral Sealant is ready to use. After suitable joint preparation and masking, the sealant is gunned into place and tooled within 5 to 10 minutes using a spatula or tooling instrument.
After tooling, tooling aids and masking tape should be immediately removed.
DOWSILTM 799 EU Glaze and Go Neutral Sealant cures reacting with atmospheric moisture. Typical properties are given for testing conditions of 23ºC (73.4ºF) and 50% R.H.
Uncured material can be removed by using a solvent. Cured material may be removed by abrasion or other mechanical means.
The sealant joint width should be designed to accommodate the movement capability of the sealant. In general, the minimum joint width should be 6 mm. For joints between 6–12 mm wide, a seal depth of 6 mm is recommended.
For joints above 12 mm wide, a width to depth ratio of 2:1 should be used, up to a maximum depth of 12 mm. For joint dimensions greater than 25 mm, please contact DOWSIL’s Technical Service Department.
In situations where fillet joints are needed, a minimum of 6 mm sealant bite to each substrate is recommended. Bond beaker tape or a backer rod should be used as back-up material to provide backpressure and avoid threesided adhesion that limits sealant movement capability.
Your DOWSIL contact details (e-mails):
Technical inquiries: email@example.com
Quality Bond: firstname.lastname@example.org
EHS inquiries: email@example.com
Reach inquiries: firstname.lastname@example.org
Your Dow Corning Construction contact details (phone):
Toll Free Numbers:
From Belgium +0800 80 522
From France +0805 54 04 39
From Germany +0800 52 50 258
From Italy +800 92 83 30
From Spain +900 813161
From United Kingdom +0800 9172 071
All other countries:
For English +32 64 51 11 59
For French +32 64 51 11 59
For German +49 611 237503
For Italian +32 64 51 11 73
For Spanish +32 64 51 11 66
For Russian +7 495 725 43 19
Fax number from all countries: +32 64 88 86 86
PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. THE SAFETY DATA SHEET IS AVAILABLE ON THE DOWSIL WEBSITE AT DOWCORNING.COM, OR FROM YOUR DOWSIL SALES APPLICATION ENGINEER, OR DISTRIBUTOR, OR BY CALLING DOW CORNING CUSTOMER SERVICE.
When stored at or below 30°C (86°F) in the original unopened containers, this product has a usable life of 12 months from the date of production.
This product is available in 205 kg drums, 310 ml cartridges, 400 and 600 ml sausages.
Do not use DOWSILTM 799 EU Glaze and Go Neutral Sealant in totally confined space because the sealant requires atmospheric moisture to cure. Bleeding can occur on porous substrates such as concrete, marble, granites and other natural stones. On these sensitive substrates, specific testing should be carried out.
DOWSILTM 799 EU Glaze and Go Neutral Sealant must be properly stored prior to use.
DOWSILTM 799 EU Glaze and Go Neutral Sealant is not recommended for structural glazing or insulated glazing applications.
DOWSILTM 799 EU Glaze and Go Neutral Sealant is neither suitable for direct food contact use, nor for direct medical or pharmaceutical applications.
To support Customers in their product safety needs, DOWSIL has an extensive Product Stewardship organization and a team of Product Safety and Regulatory Compliance (PS&RC) specialists available in each area.
For further information, please see our website, www.dowcorning.com or consult your local DOWSIL representative.
The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customer’s tests to ensure that our products are safe, effective, and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to infringe any patent.
DOWSIL’s sole warranty is that our products will meet the sales specifications in effect at the time of shipment.
Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted.
TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, DOWSIL SPECIFICALLY DISCLAIMS ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY.
DOWSIL DISCLAIMS LIABILITY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
We help you invent the future.