Two-component, solvent-free, filled, amine-cured epoxy tar mastic.
Uses
- Bonding and fi lling of most construction materials, including concrete to asphalt, especially kerbstones, and cuts in roadways.
- Tack-bonding of rubber. Bridge bearing pads to concrete stoolings.
- Bonding metal framed cats eyes to road ways (tarmac and concrete).
- Good gap fi lling properties.
- Not for structural loading, or use in drinkable water.
Advantages
- High strength, multi use.
- Resistant to motor fuels, oils and water.
Surface Preparation
Any surfaces to be treated with epidermix 315 must be LEAN, MECHANICALLY SOUND and DRY. The surface must be free of all
preparation debris prior to placing the compound.
Bonding / Priming
Self bonding.
Properties of Wet Material
Mixing ratio | 1 base: 1 activator by mass |
Density | 1.49 g/ cm3 |
Colour | Base: Black Activator: Brown Mixed: Black |
Finish | Matt |
Flash point | +120 °C |
Dilution | Do not dilute |
Toxicity | Uncured material is toxic |
Consistency | Each component is a heavy mastic |
Shelf life | 2 years from date of manufacture |
Storage conditions | Store under cover in cool conditions |
Properties During Application
Application by | Trowel or putty knife |
Pot life | 120 min/500 ml @ 25 ºC |
Volume solids | 100% |
Spreading rate | As needed up to 15 mm thickness 1 mm will require 1 L/m² |
Application temperature range |
10 ºC to 40 ºC |
Curing time @ 25°C | Initial set 4 hours Full cure: 7 days |
Fire resistance of wet material |
Non-flammable |
Properties of Cured Film
Max. service temperature | Dry: 120 ºC Wet: 70 ºC |
Compressive strength | 20 MPa |
Tensile strength | 20 MPa |
Hardness | +95 Shore D |
Toxicity | Cured film is non-toxic but don’t use in contact with food or potable liquids |
Water tainting | Will taint water |
Water resistance | Excellent |
Solvent resistance | Will resist hydrocarbons, fuels, oils and aliphatic solvents |
Chemical resistance | Resists dilute inorganic acids and dilute alkalis |
Coverage
1 L / m²/ 1 mm thick, up to 15 mm thick.
Application
Rough apply the mixed epidermix 315 to the prepared surface using a trowel or putty knife. Work the material so as to ensure thorough wetting of the surface.
A final, fair fi nish may be obtained by trowelling off the surface of the still uncured epidermix 315 with a water-wet tool.
Cleaning
abe® super brush cleaner before dried/cured.
Protection on Completion
Against traffic and spillage until cured.
Temperature and Relative Humidity
See properties during application and properties of cured material.
Model Specification
The bonding material shall be epidermix 315, a two component, solvent free, amine cured, epoxy coal tar system, applied in accordance with the manufacturers recommendations, a.b.e.® Construction Chemicals. The compound shall have a 7-day compressive strength of 20 MPa.
Packaging
epidermix 315 is supplied in 500 ml and 5l yield metal containers.
Handling & Storage
This product has a shelf life of 24 months if kept in a dry cool place in the original packaging. In more extreme conditions this period might be shortened.
Health & Safety
Wet epidermix 315 is toxic but non-flammable. Always ventilate the working area well during application and drying. Always wear gloves and eye protection when working with the material and avoid excessive inhalation and skin contact. If material is splashed in the eye, wash with copious quantities of clean water and seek medical attention.
Harmless, but not for contact with food or drinkable water.
When transporting liquids and semi liquids by aircraft, ask for material safety data sheet.
Important Note
This data sheet is issued as a guide to the use of the product(s) concerned. Whilst a.b.e.® Construction Chemicals endeavors to ensure that any advice, recommendation, specification or information is accurate and correct, the company cannot – because a.b.e.® has no direct or continuous control over where and how a.b.e.® products are applied – accept any liability either directly or indirectly arising from the use of a.b.e.® products, whether or not in accordance with any advice, specification, recommendation, or information given by the company.
Further Information
Where other products are to be used in conjunction with this material, the relevant technical data sheets should be consulted to determine total requirements. a.b.e.® Construction Chemicals has a wealth of technical and practical experience built up over years in the company’s pursuit of excellence in building and construction technology.